Project Overview :
● A self-driving vehicle, also known as an autonomous vehicle or rover, is a vehicle that is capable of traveling without human input.
● The vehicle will drive itself into the path its programed.
Requirements :
● Raspberry Pi 3 Model B+ .
● L298N Motor Driver Module.
● LM2596 DC-DC Buck Converter Step Down Module.
● DC Motors and chassis.
● Battery .
Initial setup for RPI-TENSORFLOW :
📚 Click Here , for the initial setup
Here is the image of rover,
Circuit connection :
CONNECTION TABLE :
| RPI | I/O | Components |
|---|---|---|
| 5V | OUT + | Buck converter |
| GND | OUT - | Buck converter |
| BATTERY | 12V | L298N H Bridge |
| GND | GND | L298N H Bridge |
| GPIO12 | ENA | L298N H Bridge |
| GPIO22 | IN1 | L298N H Bridge |
| GPIO23 | IN2 | L298N H Bridge |
| GPIO24 | IN3 | L298N H Bridge |
| GPIO25 | IN4 | L298N H Bridge |
| GPIO27 | ENB | L298N H Bridge |
SPECIFICATION :
Raspberry Pi 3 Model B+
The Raspberry Pi 3 Model B+ is the latest product in the Raspberry Pi 3 range, boasting a 64-bit quad core processor running at 1.4GHz, dual-band 2.4GHz and 5GHz wireless LAN, Bluetooth 4.2/BLE, faster Ethernet, and PoE capability.
The dual-band wireless LAN comes with modular compliance certification, allowing the board to be designed into end products with significantly reduced wireless LAN compliance testing, improving both cost and time to market.
● Processor: Broadcom BCM2837B0, Cortex-A53 64-bit SoC @ 1.4GHz .
● Memory: 1GB LPDDR2 SDRAM.
● Connectivity: 2.4GHz and 5GHz IEEE 802.11.b/g/n/ac wireless LAN, Bluetooth 4.2, BLE Gigabit Ethernet over USB 2.0 (maximum throughput 300Mbps) 4 × USB 2.0 ports.
● Access: Extended 40-pin GPIO header.
● Video & Sound: 1 × full size HDMI, MIPI DSI display port, MIPI CSI camera port, 4 pole stereo output and composite video port.
● Multimedia: H.264, MPEG-4 decodes (1080p30); H.264 encode (1080p30) OpenGL ES 1.1, 2.0 graphics.
● SD card support: Micro SD format for loading operating system and data storage.
● Input Power: 5V/3.1A DC via micro USB connector, 5V DC via GPIO header, Power over Ethernet (PoE)–enabled.
L298N Motor Driver Module :
● The L298N Motor Driver module consists of an L298 Motor Driver IC, 78M05 Voltage Regulator, resistors, capacitor, Power LED, 5V jumper in an integrated circuit.
● When the power supply is less than or equal to 12V, then the internal circuitry will be powered by the voltage regulator and the 5V pin can be used as an output pin to power the microcontroller.
● The jumper should not be placed when the power supply is greater than 12V and separate 5V should be given through 5V terminal to power the internal circuitry.
● ENA & ENB pins are speed control pins for Motor A and Motor B while IN1& IN2 and IN3 & IN4 are direction control pins for Motor 1 and Motor 2.
● Driver Model: L298N 2A .
● Driver Chip: Double H Bridge L298N.
● Motor Supply Voltage (Maximum): 46V.
● Motor Supply Current (Maximum): 2A.
● Logic Voltage: 5V.
● Driver Voltage: 5-35V.
● Driver Current:2A.
● Logical Current:0-36mA.
● Maximum Power (W): 25W.
● Current Sense for each motor.
● Heatsink for better performance.
● Power-On LED indicator.
DC motor :
● A DC motor is any motor within a class of electrical machines whereby direct current electrical power is converted into mechanical power.
● High torque is the biggest advantage of using DC motors in robotics.
● The direction of current flow in part of the motor is changed periodically.
● The speed of a DC motor is controlled using a variable supply voltage or by changing the strength of the current within its field wind rings.
● While smaller DC motors are commonly used in the making of appliances, tools, toys, and automobile mechanisms, such as electric car seats, larger DC motors are used in hoists, elevators, and electric vehicles.
LM2596 DC-DC Buck Converter Step Down Module
● Input: DC 3V to 40V (input voltage must be higher than the output voltage to 1.5v above cannot boost)
● Output: DC 1.5V to 35V voltage continuously adjustable, high-efficiency maximum output current of 3A
● Features: All Sanyo solid capacitors, the 36u thickening circuit boards, high-Q inductance with output value of high-power LED indicator.
Code :
import RPi.GPIO as GPIO from time import sleep m1=22 m2=23 m3=24 m4=25 pwm1=12 pwm2=27 speed=70 GPIO.setmode(GPIO.BCM) GPIO.setup(m1,GPIO.OUT) GPIO.setup(m2,GPIO.OUT) GPIO.setup(m3,GPIO.OUT) GPIO.setup(m4,GPIO.OUT) GPIO.setup(pwm1,GPIO.OUT) GPIO.setup(pwm2,GPIO.OUT) p=GPIO.PWM(pwm1,1000) p2=GPIO.PWM(pwm2,1000) p.start(speed-9.5) p2.start(speed) def f(): GPIO.output(m1,GPIO.HIGH) GPIO.output(m2,GPIO.LOW) GPIO.output(m3,GPIO.HIGH) GPIO.output(m4,GPIO.LOW) def b(): GPIO.output(m2,GPIO.HIGH) GPIO.output(m1,GPIO.LOW) GPIO.output(m4,GPIO.HIGH) GPIO.output(m3,GPIO.LOW) def l(): GPIO.output(m1,GPIO.LOW) GPIO.output(m2,GPIO.HIGH) GPIO.output(m3,GPIO.HIGH) GPIO.output(m4,GPIO.LOW) def r(): GPIO.output(m1,GPIO.HIGH) GPIO.output(m2,GPIO.LOW) GPIO.output(m3,GPIO.LOW) GPIO.output(m4,GPIO.HIGH) def s(): GPIO.output(m2,GPIO.LOW) GPIO.output(m1,GPIO.LOW) GPIO.output(m4,GPIO.LOW) GPIO.output(m3,GPIO.LOW) a=2 for i in range(a): f() sleep(1) print('Forword') s() sleep(1) b() sleep(1) print('Backword') s() sleep(1) l() sleep(1) print('left') s() sleep(1) r() sleep(1) print('right') s() sleep(1)
OUTPUT :